Coal Tar Epoxy

  • Catalog Download

  • Recommended Use

    Coal tar epoxy is two components coating excellent adhesion, hardness, impact ability proper flexibility & high elasticity resistance against humidity and corrosive environments are some of the main properties of this product. It use for protection of steel in marin structures oil – field structures, tanks, pipes, pilling, power plants, petrochemical & oil refining plants. It can be used as a protector for port establishments.
  • Surface Preparation

    -The surface should be free form any rust, moisture, mill scale, oil & grease - Mechanical & chemical surface preparation methods should be performed depending on the type of contamination, the coating system environ mental condition & the service life - For ferrous & Steel use blast in accordance with sa2 or sa2 ½ & remove all the abrasive residues & dust from the surface after sandblasting. - Apply the paint immediately followed by surface preparation .
  • Application Procedure

    - Flush equipment with recommended cleaner before use - Stir component A (base) with a Power Mixer. - Add hardener to base in the proper Mixing continue stirring for 5-10 Minutes. - After 20 – 30 minutes add Shakiba’s thinner for ready to use - Use Shakiba’s thinner for adjusting the viscosity. The consumption depends on temperature & type of equipment & thickness paint
  • Safety

    - This product is flammable it must be kept away from heat, flash & flame - keep container closed use with adequate ventilation & Earth - Prolonged & repeated contact with skin may be harmful - In case of eye contact flush with plenty of water and check with a medical doctor.
  • Note

      - Pot life, drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environmental condition. -Adjusting the viscosity & pressure. For better adhesion on un steel, we offer wash primer as on under. -This information given 25°C temperature and changed temperature cause to change data. -Don’t use different thinner; otherwise we decline all responsibilities of it. -For more information, please call to sale engineering expert.

Aluminum Epoxy Polyamide Top Coat

  • Catalog Download

  • Recommended Use

    Aluminum epoxy topcoat is a two component coating. Due to presence of aluminum pigment. This paint has an acceptable resistance against spillage of solvent, salt containing water. This product is formulated to protect metallic surfaces such as bridges,off shore structures, exterior tanks and pipes surfaces and other places where reasonable humidity and sunlight resistance are required.
  • Surface Preparation

    -The surface should be free form any rust, moisture, mill scale, oil & grease - Mechanical & chemical surface preparation methods should be performed depending on the type of contamination, the coating system environ mental condition & the service life - For ferrous & Steel use blast in accordance with sa2 or sa2 ½ & remove all the abrasive residues & dust from the surface after sandblasting.                                                         -Apply the paint immediately followed by surface preparation .
  • Application Procedure

    - Flush equipment with recommended cleaner before use - Stir component A (base) with a Power Mixer.   - Add hardener to base in the proper Mixing continue stirring for 5-10 Minutes. - After 20 – 30 minutes add Shakiba’s thinner for ready to use - Use Shakiba’s thinner for adjusting the viscosity. - The consumption depends on temperature & type of equipment & thickness paint
  • Safety

    - This product is flammable it must be kept away from heat, flash & flame - keep container closed use with adequate ventilation & Earth - Prolonged & repeated contact with skin may be harmful      - In case of eye contact flush with plenty of water and check with a medical doctor.
  • Note

      - Pot life, drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environmental condition. -Adjusting the viscosity & pressure.   -This information given 25°C temperature and changed temperature cause to change data. -Don’t use different thinner; otherwise we decline all responsibilities of it. -For more information, please call to sale engineering expert.

Epoxy Polyamide Mid Coat

  • Catalog Download

  • Recommended Use

    Epoxy Mid coat is a two component coating. This product protects the surface of steel structures against corrosion and provides an adhesion film. This Mid coat has good resistance to corrosion and abrasion such a coating system is recommended for tankers, marine tankers, storage tanks, steel structures, pipes and etc.
  • Surface Preparation

    -The surface should be free form any rust, moisture, mill scale, oil & grease - Mechanical & chemical surface preparation methods should be performed depending on the type of contamination, the coating system environ mental condition & the service life - For ferrous & Steel use as primer blast in accordance with sa2 or sa2 ½ & remove all the abrasive residues & dust from the surface after sandblasting. - Apply the paint immediately followed by surface preparation
  • Application Procedure

    - Flush equipment with recommended cleaner before use - Stir component A (base) with a Power Mixer.   - Add hardener to base in the proper Mixing continue stirring for 5-10 Minutes. - After 20 – 30 minutes add Shakiba’s thinner for ready to use - Use Shakiba’s thinner for adjusting the viscosity. -The consumption depends on temperature & type of equipment & thickness paint
  • Safety

    - This product is flammable it must be kept away from heat, flash & flame - keep container closed use with adequate ventilation & Earth - Prolonged & repeated contact with skin may be harmful   - In case of eye contact flush with plenty of water and check with a medical doctor.
  • Note

      - Density , solid contents theoretical coverage are dependent on color - Pot life, drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environmental condition. - Adjusting the viscosity & pressure. For better adhesion on unsteel, we offer wash primer as on under. -This information given 25°C temperature and changed temperature cause to change data. -Don’t use different thinner; otherwise we decline all responsibilities of it.

Epoxy PolyamineTop Coat

  • Catalog Download

  • Recommended Use

    Epoxy polyamine topcoat is a two component coating. this product has good resistance to splash and fumes of an acids, alkalis, solvent and fresh and salt water steel and off shore structures, as well as exterior tank and pipe surfaces can be coated by this paint to obtain higher resistance in corrosive environment. Such as coating system is recommended for power plants, petrochemical & oil refining and machinery.
  • Surface Preparation

    -The surface should be free form any rust, moisture, mill scale, oil & grease - Mechanical & chemical surface preparation methods should be performed depending on the type of contamination, the coating system environ mental condition & the service life - For ferrous & Steel use as primer blast in accordance with sa2 or sa2 ½ & remove all the abrasive residues & dust from the surface after sandblasting. - Apply the paint immediately followed by surface preparation
  • Application Procedure

    - Flush equipment with recommended cleaner before use - Stir component A (base) with a Power Mixer.   - Add hardener to base in the proper Mixing continue stirring for 5-10 Minutes. - After 20 – 30 minutes add Shakiba’s thinner for ready to use - Use Shakiba’s thinner for adjusting the viscosity. -The consumption depends on temperature & type of equipment & thickness paint
  • Safety

    - This product is flammable it must be kept away from heat, flash & flame - keep container closed use with adequate ventilation & Earth - Prolonged & repeated contact with skin may be harmful - In case of eye contact flush with plenty of water and check with a medical doctor.
  • Note

      - Density , solid contents theoretical coverage are dependent on color - Pot life, drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environmental condition. -Adjusting the viscosity & pressure. For better adhesion on unsteel, we offer wash primer as on under. -This information given 25°C temperature and changed temperature cause to change data. -Don’t use different thinner; otherwise we decline all responsibilities of it.

High Build Epoxy Polyamide Thixotropic

  • Catalog Download

  • Recommended Use

    This paint a two component anti - corrosive topcoat with high thickness. It is produced by epoxy resin, polyamide hardener & untoxic pigments. This paint has high adhesion with mechanical & chemical resistivity it has thixotropic property & Item be used by airless without thinner & it can be created 300-500 microns thickness with just one coating   This thixotropic paint will be creating a smooth level on the interior surface of tubes; as a result it can be prevented to pressure down. It can be used for industrial and food tankers, marine tankers, concrete & metal tanks, Gas and water tubes.
  • Surface Preparation

    -The surface should be free form any rust, moisture, mill scale, oil & grease - Mechanical & chemical surface preparation methods should be performed depending on the type of contamination, the coating system environ mental condition & the service life - For ferrous & Steel use blast in accordance with sa2 or sa2 ½ & remove all the abrasive residues & dust from the surface after sandblasting. - Apply the paint immediately followed by surface preparation
  • Application Procedure

    - Flush equipment with recommended cleaner before use - Stir component A (base) with a Power Mixer. - Add hardener to base in the proper Mixing continue stirring for 5-10 Minutes. - after 20 - 30 minutes ready to use. - Use Shakiba’s thinner for the cleaner
  • Safety

    - This product is flammable it must be kept away from heat, flash & flame - keep container closed use with adequate ventilation & Earth - Prolonged & repeated contact with skin may be harmful - In case of eye contact flush with plenty of water and check with a medical doctor.
  • Note

      - Pot life, drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environmental condition.   -Adjusting the viscosity & pressure. For better adhesion on un steel, we offer wash primer as on under. -This information given 25°C temperature and changed temperature cause to change data. -Don’t use different thinner; otherwise we decline all responsibilities of it. -For more information, please call to sale engineering expert.

IronOxide Epoxy Primer

  • Catalog Download

  • Recommended Use

    Iron Oxide epoxy is a two component coating. This product as a general purpose rust preventing primer for epoxy system, on steel and other metal surfaces, and high chemical and water resistance. If condition exists that is not within the requirement or limitations described. Such a coating system is commended for power plants petrochemical & oil refining, steel structures, and etc.
  • Surface Preparation

    -The surface should be free form any rust, moisture, mill scale, oil & grease - Mechanical & chemical surface preparation methods should be performed depending on the type of contamination, the coating system environ mental condition & the service life - For ferrous & Steel use blast in accordance with sa2 or sa2 ½ & remove all the abrasive residues & dust from the surface after sandblasting. - Apply the paint immediately followed by surface preparation
  • Application Procedure

    - Flush equipment with recommended cleaner before use - Stir component A (base) with a Power Mixer. - Add hardener to base in the proper Mixing continue stirring for 5-10 Minutes. - After 20 – 30 minutes add Shakiba’s thinner for ready to use - Use Shakiba’s thinner for adjusting the viscosity. -The consumption depends on temperature & type of equipment & thickness paint
  • Safety

    - This product is flammable it must be kept away from heat, flash & flame - keep container closed use with adequate ventilation & Earth - Prolonged & repeated contact with skin may be harmful - In case of eye contact flush with plenty of water and check with a medical doctor.
  • Note

      - Pot life, drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environmental condition. -Adjusting the viscosity & pressure For better adhesion on unsteel, we offer wash primer as on under. -This information given 25°C  temperature and changed temperature cause to change data. -Don’t use different thinner; otherwise we decline - For better adhesion on un steel , we offer wash primer as on under. all responsibilities of it. -For more information, please call to sale engineering expert .

Micaceous Iron Oxide (MIO)Epoxy Mid Coat

  • Catalog Download

  • Recommended Use

    Micaceous iron oxide epoxy is a two component coating. This product contains micaceous iron oxide, which enhances the corrosive protection & durability of the film. A three - layer system comprising epoxy primer, MIO mid coat and epoxy topcoat will result in a high performance coat. It can be use for steel surface excellent barrier property good cut ling and welding properties. Protection of structural steel in, water sewage plants, bridges storage tanks, petrochemical plants refineries.
  • Surface Preparation

    -The surface should be free form any rust, moisture, mill scale, oil & grease - Mechanical & chemical surface preparation methods should be performed depending on the type of contamination, the coating system environ mental condition & the service life - For ferrous & Steel use as primer blast in accordance with sa2 or sa2 ½ & remove all the abrasive residues & dust from the surface after sandblasting. - Apply the paint immediately followed by surface preparation
  • Application Procedure

    - Flush equipment with recommended cleaner before use - Stir component A (base) with a Power Mixer. - Add hardener to base in the proper Mixing continue stirring for 5-10 Minutes. - After 20 – 30 minutes add Shakiba’s thinner for ready to use - Use Shakiba’s thinner for adjusting the viscosity. -The consumption depends on temperature & type of equipment & thickness paint
  • Safety

    - This product is flammable it must be kept away from heat, flash & flame - keep container closed use with adequate ventilation & Earth - Prolonged & repeated contact with skin may be harmful - In case of eye contact flush with plenty of water and check with a medical doctor.
  • Note

      - Density , solid contents theoretical coverage are dependent on color - Pot life, drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environmental condition. -Adjusting the viscosity & pressure. -This information given 25°C temperature and changed temperature cause to change data. -Don’t use different thinner; otherwise we decline all responsibilities of it. -For more information, please call to sale engineering expert.

Epoxy Polyamide TopCoat

  • Catalog Download

  • Recommended Use

    Epoxy topcoat is a two component coating. It provides a glossy, level and smooth film which is resistance against scratching & abrasion as well as humidity and chemicals suitable as finish coat in various epoxy paint systems and excellent chemical resistance against weak acid and alkalis. This product is also recommended for drinking water tanks and pipes. Such a coating system is recommended for power plants, petrochemical & oil refining, machinery, steel structures and etc.
  • Surface Preparation

    - The surface should be free form any rust, moisture, mill scale, oil & grease - Mechanical & chemical surface preparation methods should be performed depending on the type of contamination, the coating system environ mental condition & the service life - Apply the paint immediately followed by surface preparation.
  • Application Procedure

    - Flush equipment with recommended cleaner before use - Stir component A (base) with a Power Mixer. - Add hardener to base in the proper Mixing continue stirring for 5-10 Minutes. - After 20 – 30 minutes add Shakiba’s thinner for ready to use - Use Shakiba’s thinner for adjusting the viscosity. - The consumption depends on temperature & type of equipment & thickness paint
  • Safety

    - This product is flammable it must be kept away from heat, flash & flame - keep container closed use with adequate ventilation & Earth - Prolonged & repeated contact with skin may be harmful - In case of eye contact flush with plenty of water and check with a medical doctor.
  • Note

      - Density , solid contents theoretical coverage are dependent on color - Pot life, drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environmental condition. - Adjusting the viscosity & pressure. - This information given 25°C temperature and changed temperature cause to change data. - Don’t use different thinner; otherwise we decline all responsibilities of it. - For more information, please call to sale engineering expert.

Red-Lead Epoxy Primer

  • Catalog Download

  • Recommended Use

    Red lead epoxy is a two component coating. This product as a general purpose rust preventing primer for epoxy system, on steel and other metal surfaces, and red lead as on anti – corrosion pigment. This primer is a heavy- Duty coating with good adhesion, hardness and reasonable resistance against water and chemical. Such a coating system is recommended for power plants petrochemical & oil refining, steel structures etc.
  • Surface Preparation

    -The surface should be free form any rust, moisture, mill scale, oil & grease - Mechanical & chemical surface preparation methods should be performed depending on the type of contamination, the coating system environ mental condition & the service life - For ferrous & Steel use blast in accordance with sa2 or sa2 ½ & remove all the abrasive residues & dust from the surface after sandblasting. - Apply the paint immediately followed by surface preparation
  • Application Procedure

    - Flush equipment with recommended cleaner before use - Stir component A (base) with a Power Mixer. - Add hardener to base in the proper Mixing continue stirring for 5-10 Minutes. - After 20 – 30 minutes add Shakiba’s thinner for ready to use - Use Shakiba’s thinner for adjusting the viscosity. -The consumption depends on temperature & type of equipment & thickness paint
  • Safety

    - This product is flammable it must be kept away from heat, flash & flame - keep container closed use with adequate ventilation & Earth - Prolonged & repeated contact with skin may be harmful - In case of eye contact flush with plenty of water and check with a medical doctor.
  • Note

      - Pot life,drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environmental condition. -Adjusting the viscosity & pressure. For better adhesion on unsteel, we offer wash primer as on under. -This information given 25°C temperature and changed temperature cause to change data. -Don’t use different thinner; otherwise we decline all responsibilities of it. -For more information, please call to sale engineering expert.

Varnish Epoxy

  • Catalog Download

  • Recommended Use

    Varnish epoxy is a two component coating. This product is based on epoxy resin and polyamide hardener for decorative and portative purposed. This varnish has high gloss & adhesion. It has high resistance in unsuitable condition Varnish can be used as a protector and coverage creative on wood surfaces, furniture, packets, brick – made, concrete & steel surfaces.
  • Surface Preparation

    -The surface should be free form any rust, moisture, mill scale, oil & grease - Mechanical & chemical surface preparation methods should be performed depending on the type of contamination, the coating system environ mental condition & the service life - Apply the paint immediately followed by surface preparation
  • Application Procedure

    - Flush equipment with recommended cleaner before use - Stir component A (base) with a Power Mixer. - Add hardener to base in the proper Mixing continue stirring for 5-10 Minutes. - After 20 – 30 minutes add Shakiba’s thinner for ready to use - Use Shakiba’s thinner for adjusting the viscosity.   -The consumption depends on temperature & type of equipment & thickness paint
  • Safety

    - This product is flammable it must be kept away from heat, flash & flame - keep container closed use with adequate ventilation & Earth - Prolonged & repeated contact with skin may be harmful - In case of eye contact flush with plenty of water and check with a medical doctor.
  • Note

      - Pot life, drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environmental condition. - Adjusting the viscosity & pressure. - This information given 25°C temperature and changed temperature cause to change data. - Don’t use different thinner; otherwise we decline all responsibilities of it. - For more information, please call to sale engineering expert.

Glass Flake Epoxy Polyamide

  • Catalog Download

  • Recommended Use

    Glass Flake is tow component epoxy coating. Excellent mechanical strength & high chemical resistance against weak acids, alkalis and high performance coating for new and old steel is outstanding characteristics. It protects both steel & concrete structures in server environments in clouding marine structures. Tank’s oil, petroleum and heavy industrial facilities and suitable sea water immersion.
  • Surface Preparation

    -The surface should be free form any rust, moisture, mill scale, oil & grease - Mechanical & chemical surface preparation methods should be performed depending on the type of     contamination, the coating system environ mental condition & the service life - For ferrous & Steel use blast in accordance with sa2 or sa2 ½ & remove all the abrasive residues & dust from the surface after sandblasting.                                                       - Apply the paint immediately followed by surface preparation
  • Application Procedure

    - Flush equipment with recommended cleaner before use - Stir component A (base) with a Power Mixer. - Add hardener to base in the proper Mixing continue stirring for 5-10 Minutes. - After 20 – 30 minutes add Shakiba’s thinner for ready to use - Use Shakiba’s thinner for adjusting the viscosity. -The consumption depends on temperature &  -type of equipment & thickness paint
  • Safety

    - This product is flammable it must be kept away from heat, flash & flame - keep container closed use with adequate ventilation & Earth    - Prolonged & repeated contact with skin may be harmful - In case of eye contact flush with plenty of water and check with a medical doctor.
  • Note

      - Density , solid contents theoretical coverage are dependent on color - Pot life, drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environmental condition. -Adjusting the viscosity & pressure. For better adhesion on steel, we offer MIO or zinc phosphate epoxy as on under. -This information given 25°C temperature and changed temperature cause to change data. -Don’t use different thinner; otherwise we decline all responsibilities of it. -For more information, please call to sale .

Zinc Chromate Epoxy Primer

  • Catalog Download

  • Recommended Use

    Zinc chromate epoxy primer is a two component coating and zinc chromate as on anti – corrosion pigment. This primer with excellent adhesion and anti – corrosive property for structural steel machinery, pipes & tanks exteriors in paper mills oil refineries, power plants, and industrial environment.
  • Surface Preparation

    -The surface should be free form any rust, moisture, mill scale, oil & grease - Mechanical & chemical surface preparation methods should be performed depending on the type of contamination, the coating system environ mental condition & the service life - For ferrous & Steel use blast in accordance with sa2 or sa2 ½ & remove all the abrasive residues & dust from the surface after sandblasting. - Apply the paint immediately followed by surface preparation
  • Application Procedure

    - Flush equipment with recommended cleaner before use - Stir component A (base) with a Power Mixer. - Add hardener to base in the proper Mixing continue stirring for 5-10 Minutes. - After 20 – 30 minutes add Shakiba’s thinner for ready to use - Use Shakiba’s thinner for adjusting the viscosity. -The consumption depends on temperature & type of equipment & thickness paint
  • Safety

    - This product is flammable it must be kept away from heat, flash & flame - keep container closed use with adequate ventilation & Earth - Prolonged & repeated contact with skin may be harmful    - In case of eye contact flush with plenty of water and check with a medical doctor.
  • Note

      - Density , solid contents theoretical coverage are dependent on color - Pot life, drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environmental condition. -Adjusting the viscosity & pressure. For better adhesion on un steel, we offer wash primer as on under. -This information given 25°C temperature and changed temperature cause to change data. -Don’t use different thinner; otherwise we decline all responsibilities of it. -For more information, please call to sale engineering expert.

Zinc DustEpoxy Primer

  • Catalog Download

  • Recommended Use

    Zinc dust epoxy primer is a two component coating. This primer is a heavy – duty coating with good adhesion hardness and reasonable resistance against water and chemicals. This product as a general purpose rust preventing primer for epoxy system, on steel and other metal surfaces. Suitable as a first coat in various paint systems. This primer has high resistance to moisture, water, industrial and marine tanks and pipe. This primer alone is not suitable for immersion in acid or alkaline solutions.
  • Surface Preparation

    -The surface should be free form any rust, moisture, mill scale, oil & grease - Mechanical & chemical surface preparation methods should be performed depending on the type of contamination, the coating system environ mental condition & the service life - For ferrous & Steel use blast in accordance with sa2 or sa2 ½ & remove all the abrasive residues & dust from the surface after sandblasting. - Apply the paint immediately followed by surface preparation
  • Application Procedure

    - Flush equipment with recommended cleaner before use - Stir component A (base) with a Power Mixer. - Add hardener to base in the proper Mixing continue stirring for 5-10 Minutes. - After 20 – 30 minutes add Shakiba’s thinner for ready to use - Use Shakiba’s thinner for adjusting the viscosity. -The consumption depends on temperature & type of equipment & thickness paint
  • Safety

    - This product is flammable it must be kept away from neat, flash & flame - Keep container closed use with adequate ventilation & Earth - Prolonged & repeated contact with skin may be harmful - In case of eye contact flush with plenty of water and check with a medical doctor.
  • Note

      - Pot life, drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environmental condition. -Adjusting the viscosity & pressure. -This information given 25°C temperature and changed temperature cause to change data. -Don’t use different thinner; otherwise we decline all responsibilities of it. -For more information, please call to sale engineering expert. -For more information, please call to sale engineering expert.

Zinc Phosphate Epoxy Primer

  • Catalog Download

  • Recommended Use

    Zinc phosphate epoxy primer is a two component coating and zinc phosphate as an anti – corrosion pigment. This primer can be coated by a variety of compatible mid/top coats such as epoxy, polyurethanes….This paint has excellent corrosion protection and it is untoxic paint the good adhesion & protective properties of this primer enable it to be used as accosting for steel structure, protector for steel& metal surfaces from humidity, power plants, storage tanks & pipes exposed to industrial environment.
  • Surface Preparation

    -The surface should be free form any rust, moisture, mill scale, oil & grease - Mechanical & chemical surface preparation methods should be performed depending on the type of contamination, the coating system environ mental condition & the service life - For ferrous & Steel use blast in accordance with sa2 or sa2 ½ & remove all the abrasive residues & dust from the surface after sandblasting.                                                - Apply the paint immediately followed by surface preparation
  • Application Procedure

    - Flush equipment with recommended cleaner before use - Stir component A (base) with a Power Mixer. - Add hardener to base in the proper Mixing continue stirring for 5-10 Minutes. - After 20 – 30 minutes add Shakiba’s thinner for ready to use - Use Shakiba’s thinner for adjusting the viscosity. -The consumption depends on temperature & type of equipment & thickness paint
  • Safety

    - This product is flammable it must be kept away from heat, flash & flame - keep container closed use with adequate ventilation & Earth - Prolonged & repeated contact with skin may be harmful   - In case of eye contact flush with plenty of water and check with a medical doctor.
  • Note

      - Density , solid contents theoretical coverage are dependent on color - Pot life, drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environtmental condition. -Adjusting the viscosity & pressure. For better adhesion on unsteel, we offer wash primer as on under.  -This information given 25°C temperatures and changed temperature cause to change data. -Don’t use different thinner; otherwise we decline all responsibilities of it.  -For more information, please call to sale engineering expert.

Three Components Zinc Rich Epoxy Primer

  • Catalog Download

  • Recommended Use

    Zinc rich epoxy primer is a three component coating. In the suitable condition, Zinc in this Primer can be creating an electrochemical protection on the surface such as galvanic condition. It gives a cathode protection film with the maximum performance on structural steel, machinery, pipes and tanks oil, refineries, power plants. This Primer alone is not suitable for immersion in acid or alkaline solution. As a versatile long-life primer steel, suitable for application on industrial structures to be exposed in severe corrosive atmospheres.
  • Surface Preparation

    -The surface should be free form any rust, moisture, mill scale, oil & grease - Mechanical & chemical surface preparation methods should be performed depending on the type of contamination, the coating system environmental condition & the service life - For ferrous & Steel use blast in accordance with sa2 or sa2 ½ & remove all the abrasive residues & dust from the surface after sandblasting. - Apply the paint immediately followed by surface preparation .
  • Application Procedure

    - Flush equipment with recommended cleaner before use - Stir component A (powder) and B (solution) with a Power Mixer. - Add component C (hardener) to base in the proper Mixing continue stirring for 5-10Minutes. - After 20 – 30 minutes add Shakiba’s thinner for ready to use - Use Shakiba’s thinner for adjusting the viscosity. -The consumption depends on temperature & type of equipment & thickness paint
  • Safety

    - This product is flammable it must be kept away from heat, flash & flame - keep container closed use with adequate ventilation & Earth - Prolonged & repeated contact with skin may be harmful - In case of eye contact flush with plenty of water check with a medical doctor.
  • Note

      - Pot life, drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environmental condition. -Adjusting the viscosity & pressure. -This information given 25°C temperature and changed temperature cause to change data. -Don’t use different thinner; otherwise we decline all responsibilities of it. -For more information, please call to sale engineering expert .

Two Components Zinc Rich Epoxy Primer

  • Catalog Download

  • Recommended Use

    Zinc rich epoxy primer is a two component coating. In the suitable condition, Zinc in this Primer can be creating an electrochemical protection on the surface such as galvanic condition. It gives a cathode protection film with the maximum performance on structural steel. Machinery, pipes and tanks oil, refineries power plants. High resistance in moderately to severely environment. This Primer alone is not suitable for immersion in acid or alkaline solution. As a versatile longlife primer steel, suitable for application on industrial structures to be exposed in severe corrosive atmospheres.
  • Surface Preparation

    -The surface should be free form any rust, moisture, mill scale, oil & grease - Mechanical & chemical surface preparation methods should be performed depending on the type of contamination, the coating system environ mental condition & the service life - For ferrous & Steel use blast in accordance with sa2 or sa2 ½ & remove all the abrasive residues & dust from the surface after sandblasting . - Apply the paint immediately followed by surface preparation
  • Application Procedure

    - Flush equipment with recommended cleaner before use - Stir component A (base) with a Power Mixer. - Add hardener to base in the proper Mixing continue stirring for 5-10 Minutes. - After 20 – 30 minutes add Shakiba’s thinner for ready to use - Use Shakiba’s thinner for adjusting the viscosity. -The consumption depends on temperature &   type of equipment & thickness paint
  • Safety

    - This product is flammable it must be kept away from heat, flash & flame - keep container closed use with adequate ventilation & Earth - Prolonged & repeated contact with skin may be harmful - In case of eye contact flush with plenty of water and check with a medical doctor.
  • Note

      - Pot life, drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environmental condition. -Adjusting the viscosity & pressure. -This information given 25°C temperature and changed temperature cause to change data. -Don’t use different thinner; otherwise we decline all responsibilities of it. -For more information, please call to sale engineering expert

Zinc Chromate –Iron Oxide Epoxy Polyamide Primer

  • Catalog Download

  • Recommended Use

    It is a two component coating base on epoxy resin and includes zinc chromate as anti-corrosive pigment so this is one of the best anti-corrosive product which is recommended in the severe atmosphere condition. It has very good adhesion to and used foe steel structure, machineries, pipes, tanks, bridges, power plants and industrial environments.
  • Surface Preparation

    • The surface should be free from any rust, moisture, mill scale, oil and grease • Mechanical and chemical surface preparation methods should be performed depending on the type of contamination, the coating system environmental condition and service life. • Apply the paint immediately followed by surface preparation
  • Application Procedure

    • Flush equipment with cleaner before use • Stir two components with a power mixer. Notice pot life time and mixing ratio • Use Shakiba`s thinner for adjusting the viscosity • The thinner should be added gradually • The consumption depends on temperature and type of equipment and thickness paint • Clean all equipment with Shakiba`s thinner .
  • Safety

    - This product is flammable it must be kept away from heat, flash & flame - keep container closed use with adequate ventilation & Earth - Prolonged & repeated contact with skin may be harmful - In case of eye contact flush with plenty of water and check with a medical doctor.
  • Note

      - Density , solid contents theoretical coverage are dependent on color - Pot life, drying time is dependent on air and steel temperature, applied film thickness. - Never apply coatings under environmental condition. -Adjusting the viscosity & pressure. For better adhesion on un steel, we offer wash primer as on under. -This information given 25°C temperature and changed temperature cause to change data. -Don’t use different thinner; otherwise we decline all responsibilities of it. -For more information, please call to sale engineering expert.